As Anyone Done Thefront Dash Speakers

MAGRIDER · 02-24-2008, 07:11 PM

AS ANYONE DONE THE FRONT DASH SPEAKERS OR GOT PICS ON HOW TO DO IT IM REALLY WANTING TO ADD SOME AND DO GUYS KNOW THE BEST SIZE TO GO WITH ANY INPUT WOULD REALLY HELP ME THANX

krewkut125 · 02-24-2008, 09:11 PM

Talk to Bigal, I think he has done this. And if not he might do it now! lol.

lowriderman3 · 02-24-2008, 09:20 PM

Mine have been replaced to include all of my interior ones, but my stereo guy did mine.

Bouch · 02-24-2008, 10:51 PM

INSTRUMENT PANEL SIDE SPEAKER

NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE).

Disconnect and isolate the battery negative cable.
Remove speaker cover from instrument panel.
Remove mounting fasteners.
Disconnect electrical harness connector and remove speaker.

INSTRUMENT PANEL CENTER SPEAKER

NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE).

Disconnect and isolate the battery negative cable.
Remove speaker cover from instrument panel.
Remove mounting fasteners.
Disconnect electrical harness connector and remove speaker.

Nate Dawg · 02-24-2008, 11:01 PM

hey that is a great schematic! Thanks for addin that to your post.

TRUEST ONE · 02-24-2008, 11:17 PM

Quote:

Originally Posted by MAGRIDER

AS ANYONE DONE THE FRONT DASH SPEAKERS OR GOT PICS ON HOW TO DO IT IM REALLY WANTING TO ADD SOME AND DO GUYS KNOW THE BEST SIZE TO GO WITH ANY INPUT WOULD REALLY HELP ME THANX

I'm not sure if you can fit anything other than a 3 1/2 inch. speaker in that opening. Hmmmm.....let the modding begin!!!!

Bigal470 · 02-24-2008, 11:26 PM

fyi ^^^ that diagram is of the 300c much more involved in the mag

the dash takes 3.5 inch speakers

here is a quick step by step
1)remove a pillar covers - be careful doing this once the top pops out it has a little clip you need to remove from behind if you pull to hard you will break it
2)remove heat defuser - this is the long plastic thing along the window its held on by the same snap clips as everything else on the dash once you have it off make sure all the clips are on the defuser before you put it back on it will make it easier to install and help make sure you dont have any rattles
3)run wire to stereo - with the top of the dash off and the stereo out this is easy you can also remove the under dash covers to make it even easier.
4)connect + & - wires to the speaker
5)install speaker - they usually only take two screws
6)splice wires into front speaker leads - do a search for the wiring diagram dont have it handy
7) \re install your stereo and crank up the tunes

**Braddah Jay** · 02-24-2008, 11:27 PM

I put a 4" mid in mine with the help of a dremel tool. I have JL Audio 3-way component set for the front. I'll try to dig up some pics........

MAGRIDER · 02-25-2008, 04:55 PM

Hey Thanx Guys A Lot Of Good Input I Love Pics But I Think I Can Figure It Out But Thanx Again

02-24-2008, 07:11 PM	#1
MAGRIDER Junior Member Join Date: Feb 2008 Location: Salt Lake City Posts: 27 iTrader: (0)	As Anyone Done Thefront Dash Speakers AS ANYONE DONE THE FRONT DASH SPEAKERS OR GOT PICS ON HOW TO DO IT IM REALLY WANTING TO ADD SOME AND DO GUYS KNOW THE BEST SIZE TO GO WITH ANY INPUT WOULD REALLY HELP ME THANX

02-24-2008, 09:20 PM	#3
lowriderman3 Respect My Authoritah! Join Date: Jul 2006 Location: South GA Posts: 2,673 iTrader: (0)	Mine have been replaced to include all of my interior ones, but my stereo guy did mine.
	lowriderman3's Sig: Check Out My Car Domain Page

02-24-2008, 10:51 PM	#4
Bouch Member Join Date: Jul 2007 Location: Edmonton, Alberta Posts: 58 iTrader: (0)	INSTRUMENT PANEL SIDE SPEAKER NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE). Disconnect and isolate the battery negative cable. Remove speaker cover from instrument panel. Remove mounting fasteners. Disconnect electrical harness connector and remove speaker. INSTRUMENT PANEL CENTER SPEAKER NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE). Disconnect and isolate the battery negative cable. Remove speaker cover from instrument panel. Remove mounting fasteners. Disconnect electrical harness connector and remove speaker.
	Bouch's Sig:

02-24-2008, 11:01 PM	#5
Nate Dawg Member Join Date: Jan 2008 Location: North Carolina Posts: 34 iTrader: (0)	hey that is a great schematic! Thanks for addin that to your post.
	Nate Dawg's Sig: Nate Dawg From NC

02-24-2008, 11:26 PM	#7
Bigal470 One wicked azz car! Join Date: Oct 2006 Location: Oceanside, CA Posts: 4,406 iTrader: (0)	fyi ^^^ that diagram is of the 300c much more involved in the mag the dash takes 3.5 inch speakers here is a quick step by step 1)remove a pillar covers - be careful doing this once the top pops out it has a little clip you need to remove from behind if you pull to hard you will break it 2)remove heat defuser - this is the long plastic thing along the window its held on by the same snap clips as everything else on the dash once you have it off make sure all the clips are on the defuser before you put it back on it will make it easier to install and help make sure you dont have any rattles 3)run wire to stereo - with the top of the dash off and the stereo out this is easy you can also remove the under dash covers to make it even easier. 4)connect + & - wires to the speaker 5)install speaker - they usually only take two screws 6)splice wires into front speaker leads - do a search for the wiring diagram dont have it handy 7) \re install your stereo and crank up the tunes
	Bigal470's Sig:

Remove Advertisements Sponsored Links
Supporting Members do not see these ads.

02-24-2008, 09:11 PM	#2
krewkut125 Senior Member Join Date: Sep 2007 Location: Palm Bay, Florida Posts: 2,883 iTrader: (0)	Talk to Bigal, I think he has done this. And if not he might do it now! lol.

02-24-2008, 11:27 PM	#8
Braddah Jay "Need for more speed!!!" Join Date: Apr 2007 Location: Driving the SRT life in Palmdale,Cali Posts: 773 iTrader: (1)	*I put a 4" mid in mine with the help of a dremel tool. I have JL Audio 3-way component set for the front. I'll try to dig up some pics........*
	Braddah Jay's Sig:

02-25-2008, 04:55 PM	#9
MAGRIDER Junior Member Join Date: Feb 2008 Location: Salt Lake City Posts: 27 iTrader: (0)	Hey Thanx Guys A Lot Of Good Input I Love Pics But I Think I Can Figure It Out But Thanx Again

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode